Preface

Spring! Finally!

Our favorite season has arrived, fresh green colors in most parts of the Northern hemisphere transform nature and parks in pieces of art. The blooming of nature each time after the Winter is a spectacle by no means to be sneezed at. It brings hope and you notice it immediately on people. In the streets, in shops, just around you, in your favorite club or even at work. When you are honest with yourselves you see it even in your mirror, yes we too are changing when new fresh green leafs are blooming. The young animal awakes in us, each springtime again, as a playful foal in the meadow, and that’s good for sure!

Will the economy also revive happy as a young foal in the meadow ? I’m afraid that I can’t show the same optimism. We’re floating away economically. That’s logical, the Western economy is based on the fact that profits go to the rich and debts to the State. When Forbes announced at the beginning of March the top of Dollar multimillionaires , it strikes me how much richer the wealthy citizens of our planet have become, most of them have just doubled their capital in a couple of years. It’s not their fault of course, they’ve previously laid the foundation for it, it’s just owing to the system. On the other hand poverty is expanding too.

This uncertainty appears to bring along a huge potential for our sector. Inflation is high, the ECB is stamping a great deal of money in order that the monetary crisis will not turn out into a great depression. Apparently black Thursday and the depression of the Thirties are still in our mind. Consequently a massive inflation can’t be turned away. Nowadays money on the bank costs more than it yields . In other words interest rates are lower that the inflation. Many people wish therefore to invest their money in something concrete and let our oldtimers just be the hit of these new technologies. Prices of top cars are rising to unknown heights throughout the world. When the top of the mountain is rising, the base will inevitably become wider and just right there we are with our Volkswagen story at the flank of the economical mountain. We all can only become better from it.

Being a wholesale company we are ready to assist our distributors. Our stock is bigger than ever and our logistics are sharp. We’re prepared for the new season and we’re looking forward to work at full speed. Now we’ve got used to our new infrastructure we can pick quicker, pack better, deliver more, we’re just ready to encounter this beautiful season together with our customers.

My Spring greetings are to wish you all, customers, suppliers, friends and sympathizers that all your dreams come true, happy as a foal in the meadow and if possible even a bit more….

No longer available

• # 0012-5 Bumper 75- front (USA)
• # 0013-5 Bumper 75- rear (USA)
• # 2533 Centercap sticker Empi (4)
• # 2533-1 Centercap sticker Empi GTV
• # 9505 F4 Chromol. lightened flywheel 200mm(5.5kg)
• # 9532-100 F4 Sprintstar centercap
• # 0348 Rear Window louvres Type 1 53-57

Price modifications are indicated on the pricelist itself!

Winddeflector for sliding roof, green

0390-003  Type 1

Winddeflector for sliding roof, brown

0390-005  Type 1 As temperatures rise we start to drive our Volkswagens more regularly and, when possible, in open air. Ragtop Bug cruises are very enjoyable but sometimes it is just that bit to cold. Therefore BBT started since 06/2009 production of the transparent white wind deflector for these ragtops. This extraordinary practical accessory is a reproduction of the original from the fifties. It’s quick and easy to assemble at the front of the sliding roof. This deflector makes driving wind will be directed upwards i.o. into the car, which gives a luxurious feeling during long drives. With this accessory you can drive during 9 months a year topless without losing any comfort, even in Western Europe! The deflectors have been made out of transparent plexi and are now also available each from stock in green (# 0390-003) and brown (# 0390-005).

Safari window lock, left

0397-010  Type 2With these new products it will be perfectly possible to restore the front Safari windows of -07/67 Type 2 buses or to keep them in optimal condition. Item # 0397-100 is used with pop-out side windows and is to replace corroded or damaged items. Each part is available separately from stock.

Safari window lock, right

0397-011  Type 2

Safari body seal front

0397-050  Type 2

Safari glass seal front

0397-060  Type 2

Side pop-out hinge

0397-100  Type 2

Clip for guiding roll for support spring

0438-281  T2 -ch 214 2057 948/ -73N12 435 1
Clips to secure the guiding roll support spring (#0438-280) for correct assembly of the engine lid support spring was still missing in our range. From now on available each from stock.

Door check strap

0438-600  Type 2 -07/60211 841 387
Side doors of -07/67 buses are designed  as such that they can be completely opened without problems. Therefore there is a maximal access to the rear passengers and/or cargo part. In order to avoid damage  to the body when doors open wide, VW has created a door check by means of a textile strap which is fixed at the underside of the side doors. These straps are made of textile and due to age they are often torn. From now on we can deliver them both, versions differing in length, each from stock.

Door check strap

0438-610  Type 2 08/60-07/67265 841 387

Cabine door lock catch, left

0438-750  Type 14 56-07/63141 837 295
Many owners of Karmann Ghia can confirm that the body hasn’t the same rigidity  as the VW Beetle. That’s why a good locking of the doors is sometimes a quiet susceptible part with Karmann Ghia. Due to friction on the body, parts related to suspension and securing  the doors can suffer a lot and also the lock catches don’t escape this wear and tear wastage. When traveling you will surely like that doors are kept locked and as lock catches are the principal part, we’ve decided to take this item for model -07/63 into our program. Lock catches are sold each and per side. 

Cabine door lock catch, right

0438-751  Type 14 56-07/63141 837 296

Filler flap

0492-750  Type 14 08/67-This rubber flap can be found behind the fuel filler cut off valve in the front wing on Karmann Ghia 08/67- models. The seal gets damaged under the influence of petrol vapors and drying and it can no longer accomplish its protective function. From now on we can deliver this flap each from stock.  

Filler neck rubber hose

0492-855  Type 2 08/71-07/79211 201 125D
The distance between filler neck and fuel tank with Type 2 from model 08/71- is bridged by means of metallic parts and rubber hose. Due to influences of fuel and petrol vapors this rubber hose parts can get fragile, tear and leak. Leakage has to be avoided any way, as it has already caused fire in the engine compartment for several times in the past. From now on we can deliver this filler neck rubber hose, which connects to the fuel tank, each from stock.

Dashboard moulding kit with clips

0525-500  Type 1 08/57-07/67113 853 241A + 113 853 243A + 113 853 245A + 113 853 247A
This aluminum dashboard molding kit is already for quite some time for sale in our local shop in St.-Job-in-'t-Goor as an alternative for used dashboard moldings. In the meantime our stock of second-hand moldings has reduced a lot, which has made us decide to take this set now as a continuously available part in our program. The set contains 4 moldings and corresponding PVC clips and is designed for assembly on the dashboard without providing for petrol gauge.

Headlight USA, superior quality

0600-010  Type 1 -07/67We’ve been offering for a long time the European version of the -07/67 Type 1 and Type 2 headlight from Hella in a good quality (# 0600-1/0600-5/0600-6/0600-7/0600-8). The demand after an European version from Bosch and good US versions of this -07/67 headlights has resulted in an extension of our assortment. # 0600-010 is the US version of the Type 1 headlight with transparent glass and foreseen for sealed beam lights. # 0600-050 and 0600-060 are the US versions for Type 2  -07/67 with the same composition as previously stated. # 0600-150 is the European version with profiled lenses in Bosch version. Above mentioned headlights are available each from stock, except for Type 2 they are available per side.

Headlight USA, left, superior quality

0600-050  Type 2 -07/67

Headlight USA, right, superior quality

0600-060  Type 2 -07/67

European headlight

0600-150  Type 1 -07/67, Bosch 111 941 039 (Bosch)

Hazard switch, universal, 7 connections

0636-290 With the actual traffic it is essential to drive with a good electrical installation and proper lighting. This applies also on the indicator switches, which were installed on Type 1 Beetles from the late sixties with an hazard indicator signals function, so that in case of danger or breakdown all the 4 indicator signals could be ignited. Many owners of older models wish to provide their vehicle with this function too. The classic hazard switch with indicator light and connection code according to numbering used by Volkswagen that BBT has now in its range, can be installed in a correct way on older vehicles.

Battery, positive pole left, Type 2

0638-100  12V 44ah/220AWe strive for completing our offer of batteries and upon request of some among you, we’ve therefore decided to take into our assortment also batteries suitable for Type 2 with connecting poles at the same side. Connecting and disconnecting the battery will be no longer a risky undertaking that puts to the proof our elasticity, and if some cases even our self-image. Available each from stock.

Fuse box bakelite for 2 fuses

0662-475  Type 1 01/54-08/59111 937 041 + 111 937 455
These fuse boxes are a nice alternative for your torn or corroded item. The fuse box with 2 fuses can be found on Type 1 from 01/54-08/59, the one with 4 fuses is used on type 1 10/52-08/60 and the version foreseen with 6 fuses can be found on Type -01/54 and Type 2 -06/60. The fuse boxes are delivered with cover and screw inclusive and are foreseen of 8A fuses.

Fuse box bakelite for 4 fuses

0662-485  Type 1 10/52-08/60111 937 205 + 111 937 255

Fuse box bakelite for 6 fuses

0662-495  Type 1 -01/54

Type 2 -06/60

111 937 031

Fuse box clip

0662-590  Type 1/2 08/59-07/71111 937 591
This clip is a typical part which gets easily lost during restoration of your VW Beetle or Bus. The clip fixes the fuse box in the body. Due to its special design it’s not an easy thing to find for sale, which can lead to some annoyance when finishing your project. From now on we can deliver them each from stock.

Turn signal switch

9 wires

0668-820  T2 08/65-07/67211 953 513E
Courteous drivers make often use of the direction indicator switch and therefore this part is very subject to wear and needs to be replaced once in a while. The indicator switch that we are offering now is destined for assembly on Type 2 buses from 08/65-07/67 and has 9 wires. Delivered each.

Dome light switch

0686-150  T1 10/52-01/54 113 947 561
This switch can be found on Type 1 Beetle 10/52-01/54 near the A-post just beneath the door catchers. The switch puts the interior light on when you open the doors. When they are old and corroded it’s possible that they don’t give a good contact anymore. From now on we can deliver you this new exemplar each from stock.  

Dome light dashboard switch

0686-155  Type 1 10/52-01/54 151 947 511A
It’s possible with this switch to put on the interior light manually. Originally it has been applied on Type 1 10/52-01/54, but it is perfectly possible to use this classic looking switch on other applications. Available each from stock.

Interior light holder

0687-210  T2 -07/67211 947 107A
This version of the interior light was already available under ref. #0687-20 in our range, however due to continuous problems with the quality of this item, our purchase department has been looking for a better alternative. #0687-210 and the corresponding lens #0687-215 are the perfect replacement for your old and damaged interior light. The holder as well as the lens are available each and separately. 

Interior light lens

0687-215  T2 -07/67211 947 125A

Interior light, convertible

0688-100  T1 08/64-07/67

KG 08/64-07/67

151 947 111B
The interior light for Type 1 convertible and Karmann Ghia 08/64-07/67 is made of transparent PVC, in which is located a switch mechanism. This combination makes that the old lamp holder gets fragile and breaks when manipulated. We’ve now a nice reproduction available from stock to replace the damaged item. Sold each, bulb separately.

Inspection cover seal

0702-100  Type 1 -07/65At the front of a Type 1 Beetle body you can find a cover plate which is sealed with a rubber. After disassembly of this plate you get access to the inside of the body shaft and you can for instance take out the shift shaft from the body. The seal that sits between this cover plate and the body is often putrefied that it has to be replaced. From now on we can deliver this seal each from stock.

Front indicator rubber, each

0759-410  Type 14 -11/58141 953 165
This indicator seal is located at the front side between the body and the indicator housing and seals these 2 parts to avoid damages to the paint. After many years these seals are generally hardened and need to be replaced. From now on we can deliver them each from stock.

Seal taillight, as pair

0759-510  Type 14 56-07/59141 945 177A
These taillight seals are an extension of our wide range of taillight seals for Karmann Ghia and they are a perfect alternative to replace the -07/59 Karmann Ghia taillight seals. Available from now on per pair from stock.

Seal taillight lens, as pair

0759-515  Type 14 56-07/59141 945 173

Coat hook in cloud white

0784-750  Type 2 08/63-79221 857 629A
Influences of UV rays come into sight after many years on many interior parts in our classic VW. Parts in PVC fade and harden. Damages due to manipulation or disassembly during repair can’t be avoided, which requires availability of such replacing parts. The PVC coat hook used on Type 2 08/63-07/79 is such a part that we present now in a nice reproduction each from stock.

Floor pan with seat hump, left

0854-350  08/72-

1303

This floor plate with installed hump will help many Type 1 lover, who want to replace the floor of the body. In the past we already had these floor plates (# 0854-3 & 0855-3), though the hump (# 0882-L & 0882-R) weren’t delivered along with the floor plates and had to be ordered  and assembled separately. Another option was the recycling  and assembly of  the old hump on the new floor plate, but this is certainly not the most efficient proceeding. From now on we can deliver the floor plate each and for each side from stock.

Floor pan with seat hump, right

0855-350  08/72-

1303

Bumperretainer on plate rear, left

0889-370 A Karmann Ghia with a perfectly rust free body is a hardly seen phenomenon, partly due to the production process, the underside of this car is often damaged by rust. Year in year out BBT has worked  very hard to take a good quality of body plates for Karmann Ghia in our range.  We’ve always given priority to parts very susceptible to rust and partly due to the feedback of our customers we have decided to take these rear bumper retainer parts in our assortment. From now on available in a good quality each for each side from stock.

Bumperretainer on plate rear, right

0889-371

Front side bumper bracket

0890-030  Type 2 -07/67These clips for assembly of the bumper bracket are principally a fix part of the body and you can find them near the side steps of the cabin with Type 2 buses -07/67. These clips are essential for a correctly positioned assembly of the front bumper end caps. The side steps are very susceptible to corrosion and also the accompanying brackets can get damaged. From now on we can deliver you them each from stock in a reproduction of good quality.

Rear wheel arc, left

0890-345  -07/62 For many years we were able to deliver the rear wheel arches as a replacing part for Type 2 model from 08/62-07/67, which in some cases after being adapted, could also be used on -07/62 model. In the meantime we have found through our expanded network the correct model in a good fitting quality. As a result of this fine quality, we have taken both versions from our supplier into our range. Available each for each side.

Rear wheel arc, right

0890-355  -07/62

Inner center sill, left

0891-160  Type 2 08/67-07/79211 809 583A
This inner center sill can be found on Type 2 buses at in the inside of the thresholds. Everybody knows that this part is the first of the body parts which can get damaged by corrosion. Now you can repair the damages without problems with these repair plate work. The inner sill is available each per side.

Inner center sill, right

0891-161  Type 2 08/67-07/79211 809 584A

Jacking point complete rear, left

0891-597  Type 2 08/67-07/79211 703 119A
The rear jacking points for Type 2 buses are very susceptible to rust, because of their position underneath the car, where dirt, humidity and road salt can do their destructing job. Using the jacking point and placing the jack  on the wrong place, can damage the jacking point and impede repair. BBT offers you now a good jacking point with body part from stock, so that you can replace it in a reliable way. Available each and for each side.

Jacking point complete rear, right

0891-598  Type 2 08/67-07/79211 703 120A

Chrome moulding front grill

0891-986  Type 2 08/67-07/72241 853 215
On Type 2a Deluxe buses there is a molding around the air inlet at the front, which gives a very nice luxurious finish. However this molding has often lost its gloss on many of these buses. A replacing exemplar can only solve this problem. From now on you can obtain this molding at BBT or one of its distributors in a polished aluminum version, which can be perfectly used to replace the old one or as surplus on standard buses.

Gas cable

0910-005  Type 1 2660 mm, -10/52 (ch. -1 397 022)111 721 555
Split window beetle drivers are no longer forced to customize when the accelerator cable is broken or damaged by corrosion. From now on we can offer a perfect fitting alternative from stock.

Handbrake cable for lever shocks

0920-020  Type 1 3038 mm, -07/55 (- ch. 1 929 745)113 609 721
These handbrake cables are indeed a very important part in the brake section of our beloved car. They must be in mint condition for a proper functioning without sorrows. Infiltration of dirt, humidity and dust during a long standstill can cause corrosion and cables get stuck. These cables can be released sometimes with some skill and luck, though in reality damage is often so important that they have to be replaced after all. From now on we can deliver your these cables for pre-07/88 beetles foreseen of an hydraulic brake system and the applied  rear axle shock absorber systems. Available each and per side from stock.

Handbrake cable for telescopic shocks

0920-025  Type 1 3138 mm, -07/55 (- ch. 1 929 745)113 609 721A

Front hood outer cable

0962-250  Type 14 08/67-74143 827 545
The cable that unlocks the Karmann Ghia front hood runs from model year 1968 in a PVC hosing through the front hood. This hosing prevents that the cable gets clamped or damaged, though when they are old the outer cable can harden. Consequently this protection can  break and tear when manipulating. The adjustment of the front hood cable is no longer properly working and you can’t unlock the front hood anymore. We recommend to replace the damaged outer cable at the first signs of age by a new correctly fitting item. Available each from stock.

Abarth exhaust

stainless steel

1053-11  1200ccSince June 2005 BBT has for you this nice reproduction of the Abarth exhaust in stainless steel  for 25-30HP engines (# 1053-10). in production The solidity of this exhaust resulted in an increasing demand for 1200cc and 13-1600cc engines too, it has incited us to develop a  convenient exhaust for these kind of engines. We’ve them already  available for 13/15/1600cc engines(1053-12) since end 2010 and from now on we can deliver also for 1200cc engines  an appropriate reproduction of the Abarth exhaust in stainless steel from stock!

J- tubes 25-30 hp

as pair

1080-850Heat exchangers of 25 & 30 H.P. engines have been the first attempt of Volkswagen to heat the engine block as well as the interior. Heat exchangers recover the warmth through exhaust tips and just these exhaust parts are very susceptible to corrosion caused by changes in temperature and influences of exhaust gas. For a long time BBT has these tubes to repair the heat exchangers in its range, though in the past one had to recycle the connecting flanges of the old exhaust tips. From now on we have an improved and more complete product available. Tubes are sold a pair, inclusive the flanges that you’ve still got to weld.

End play measuring tool

1119-000

Hog Ring kit

1160-000When upholstering the seats clips are used to secure the upholstery underneath the seat frame. These clips are un their turn assembled by using a special plier. From now on we can deliver clips and plier as a set, sufficient for finishing 1 car.

Adapter kit brake caliper

1248-095  Type 2 08/72-07/85 - Type 2 08/69-07/72It’s possible to use the brake calipers of Type 2 08/72-07/85 with this adapter kit and to adjust them on the original spindle nuts of model 08/69-07/72. This is a practical alternative to replace the original damaged 08/69-07/72 brake calipers, which new are no longer available. From now on this adapter kit is available as a set for 1 vehicle from stock.

King pin bushing

1337-045  Type 2 08/62-07/67211 405 317B
This king pin bushing can be found on Type 2 Split buses from 08/62- in the upper and lower pen lugs of the spindle nut. Due to heavy use and/or poor greasing these bushings can get damaged and need to be replaced by a new item. From now on we can deliver these bushings each new from stock. For the revision of the spindle nuts of 1 bushing your need 4 of them.

King pin set

1338-006  Type 2 08/62-07/63211 498 021A
Suspension parts remain a sensitive part on Split buses, a regular control and professional repair when worn or defective is absolutely required if you want to enjoy trips without problems. Having  this purpose in mind we have taken this king pin set for Type 1 model year 1963, ch 999 305 - 1 144 281 into our range. The set is delivered as repair of 1 complete shaft /2 sides.

Seals suspension arms, original, 4 pieces

1373-500  Type 2 08/67-07/79211 405 129A x4
These seals have the purpose to close the connection between the suspension arms and the front axle with Type 2 buses from 08/67-07/79, so that grease remains in the front axle and prevents that sand and humidity can enter into the front axle stock. This last fact can have very destructive consequences on the front axle bearing and suspension arms running surface. So it’s better to replace  torn and hardened items immediately. We can deliver these seals per 4 pieces in original VW quality.

Grease nipple

1396-101  M10x1N 18 530 1
Type 1 and Type 2 front axles have a couple of lubrication points which can be lubricated by means of grease nipples. These grease nipples can get damaged due to corrosion or manipulation upon repair or restoration of the front beam suspension parts. From now on we can deliver you these M10 nipples in 3 different versions. We already had the M8 version of these grease nipples for lubrication of the front axle for quite some time in our range under # 1396-1. From now on these grease nipples are available separately from stock.

Grease nipple, angle from 45°

1396-102  M10x1

Grease nipple, angle from 90°

1396-103  M10x1N 018 516 1

Boots for gear linkage bushing rear, as pair

1409-560  Type 25 08/87-251 711 167F x2
The shift part on Type 25 buses consists of a relatively complex unit of gear linkage, shift parts and boots, which should all be in good condition. On this condition only shifting gear can go smoothly and damage at the gear box will be prevented. #1409-560 is the boot that protects the rear gear linkage against dirt and humidity. #1409-600 is the gear shift joint on  the gearbox. It is manipulated through an elbow gate. Due to frequent use this joint can wear off and turn out to play. This play will immediately provoke bad shifting. Both parts are available each from stock.

Gear shift joint on gearbox

1409-600  Type 25 08/82-251 711 221F

Bolt for H-Beam connecting rods

1602-295In competition such as crossing and drag racing the revision of the engine is a returning event, where many components of the engine block are used for several times. This applies also on the H-beam connecting rods, like those we present under # 1602-15 -> 1602-23. The bolts for assembly of these rods are nevertheless less appropriate to be used again and we recommend to replace them upon each revision. We can offer these bolts in a good quality each from stock.

Rebuild connecting rod, Brazil

1603-315  13/1600cc 08/59-Our classic aircooled VW boxer engine has the reputation to be indestructible, however this doesn’t mean that it doesn’t ever need any revision. Parts such as engine case, crankshaft, cylinder heads, but also rods have to be revised once in a while. Wear and damage can be that serious, that parts must be replaced. We can deliver you since shortly the original VW rods from stock, so that the revision of your 13/1600cc engine block can be done properly. Rods are  sold per set of 4 for 1 engine and they are foreseen of the wrist pin bushings.

Valve spring, each

1735-500  Type 4021 109 623E
Since January 2011 we offer you the opportunity to buy cylinder heads for aircooled Type 4 engines to replace damaged items (# 1721-800/1721-810/1721-020/1721-030/1721-040/1721-050). You don’t have to replace the entire cylinder head, but revision can offer a solution. Valves, cones of valve, valve conductors… we can deliver them all from stock, but until now we hadn’t the valve springs for sale, which is also a part very susceptible to use. We can deliver them from now on each from stock for all aircooled type 4 engines.

Oil cooler adapting seal kit, 8 mm to 10 mm

1824-200This oil cooler adapting seal is designed for assembly of an oil cooler installed outside the fan shroud on single port Type 1 based engines, of which  the oil cooler used to be originally assembled directly on the engine case. In this way it’s possible to obtain the same cooling capacity for a single port Type 1 engine without harming  the original look. Sold per set for assembly on 1 oil cooler.

Oil cap seal

1847-250  12/1600cc Type 1 -79

Type 14

Type 2 -07/79

111 115 487
The oil cap seal is originally made from cork, though the cap will harden and crumble after many years. The sealing function will consequently  be reduced and the risk that small parts of the cork will get into the motor oil is quite considerable. We can deliver you from now on a correct fitting and oil resistant seal each from stock.

Crankcase breather filter

1896-100 This universal filter applies on the crankcase breather filter and can be connected with its 12mm connection directly on the crankcase ventilation. Of course, you can chose, according to proper wishes, any other convenient place for this filter. Available each from stock.

V-belt 25 hp

1941-050  Type 1 13 x 900111 903 137
The pulley belt for 25 HP engines have a different measure than those used nowadays. That’s why it isn’t easy to find  replacing or  spare parts for this belt. For many years the correct measure was for  for sale in our shop only, but due to an irregular availability it wasn’t possible to take it into our program. Fortunately things have changed and now you can replace the used or torn belt by a new item. Available each.

Blue coil with clamp, Beru 12V

2051-250We had to make already for several time quite some efforts to guarantee availability of the well-known blue 12V coils. That has incited our purchase team to look and to achieve for an fitting alternative and now we can offer you a nice coil from the German brand Beru. Beru exists since 1912 and is one of the 4 biggest suppliers and developers of ignition systems for diesel-powered vehicles. They have since 1989 ignition coils in their offer, which we can deliver now from stock. The quality of this coil is equivalent to the Bosch version and is delivered each, assembly clamp inclusive.

Vacuumhose from 28PCI carburettor to distributor

2079-250111 129 493A + 111 129 495 x2
You can find a metallic hose on 25 & 30 H.P. engines equipped with a 25PCI carburetor between carburetor and vacuum unit, which has been replaced by a flexible rubber hose on later models. This hose can get obstructed or damaged by handling after many years  and needs to be replaced. We offer you now a substitute from stock.

Rubber tube between carburettor and air filter

2147-100  Type 2 08/63-07/67

Type 14 08/65-07/66

211 129 627
This sleeve takes care on Type 2 08/63-07/67 and  Karmann Ghia 08/65-07/66  of the connection between air cleaner and carburetor, so that only filtered air can get into the combustion components. Temperature fluctuation and corrosion by oil and petrol vapors can render the sleeve fragile and porous. It gets damaged and there is no longer a good sealing. From now on you can replace your damaged item.

Velocity stacks IDF 38 mm

as pair

2196-490These velocity stacks are an extension of our existing range and with their 38mm height they are the lowest version available from stock. These stacks are available per pair for 1 carburetor from stock.

Pre-heater pipe to aircleaner

2219-100  Type 1113 119 519G
Correctly assembled engine plate work is essential for a proper functioning without problems of your aircooled engines. That’s why it is important that plate work is in optimal condition. Corrosion caused by temperature fluctuations and weather influences can seriously damage the plate work, so that it can’t be no longer used. The pipe which is now in our range can be found near the V-belt driving disc. Its function is to intercept the pre-heated air, that comes between the cylinders and the cylinder head. The heated air is captured through this pipe and guided to the carburetor by means of the air cleaner, in order to achieve an optimal substance for an effective combustion. This pipe is available each from stock.

Wheel Misano, black

14 x 5.5

5 lug (5x112)

ET +39

2572-200  Type 2 08/71-07/79

Type 25 05/79-07/92

The aluminum ‘Misano’ wheel, that is in production with one of our Italian distributors, Dei Käfer Service, is BBT’s newest acquisition to enlarge our range for Type 2 and Type 3 bus wheels. This very nice wheel is available in black with polished rim and has following measures; 5.5" x 14"/ 5x112 ET39. Available each from stock, centercap inclusive, but without assembling bolts.

Speedometer light bulb holder, screw connection

2692-040  Type 1/ Type 2 111 957 397
Your damaged speedometer light bulb holders with screw fitting can be replaced from now on without problems by these nice reproductions. Available each from stock.

Front seat release knob

1 seat

3184-100  Type 1 12/66-07/72

KG 08/67-01/72

Type 2 08/67-12/69 M13

113 881 633C/D
The seat release knob and  guide, that we have taken now in our range are indispensable parts which enable the release and pulling forward of the seat. In this way only it’s possible for passengers to take a seat at the back of the vehicle. The knob and the guide can be found on Type 1 and Karmann Ghia at the outside of the back of the front seat, whereas it is also used on Type 2 buses 08/67-12/69 to release the 2nd row of the seat back (option code M13 / 8 places). This button is often hardened and torn, as a result of which it doesn’t stay in place or gets lost. From now on button and guide are available each from stock.

Guide for seat release knob

1 seat

3184-200  Type 1 12/66-07/72

KG 08/67-01/72

Type 2 08/67-12/69 M13

113 881 607

Exhaust, Vintage Speed, with pre-heat risers, Stainless steel

3280-200  Type 2 08/59-07/67 We’re enlarging our range with these exhausts in stainless steel of good quality and offer you the possibility to find the adequate exhaust for your Type 2 bus. For buses from 08/59-07/67 with an engine block based on Type 1 13/1600cc we have the version available which can be assembled on standard height as was as lowered buses with an engine capacity of 125 HP. For buses with engines based on Type 4 manufactured until 07/79 we have also this very apt exhaust available. Exhausts are sold each from stock with accompanying gasket kits and assembly material.

Exhaust, Vintage Speed, Stainless steel

3280-250  Type 4

Headrest padding

3590-000  Type 1 08/67-07/69The paddings to repair the seats and backs parts were already for some time available in our range, though we were still missing the separate headrest paddings. Meanwhile we have found a solution. Made from foam rubber, which joins nicely up on the back padding  parts already available from stock. There are 3 different models available for each own version depending on the model year. Available each from stock.

Headrest padding

3591-000  Type 1 08/69-07/72

Headrest padding

3593-000  Type 1 08/76-

Tow hitch, Westfalia model

4850-200  Type 2 08/58-07/67For many among us, VW enthusiasts, nothing speaks more to our imagination than travelling in our beloved Volkswagen. It’s not different for those who own a split bus and we see this each time when we attend a meeting or organize a convoy. We often love to take some extra facilities on our trips and a trailer for additional equipment and/or back-up or a caravan for extra sleeping accommodation belong also to these facilities. A tow hitch is therefore essential. BBT offers you this tow hitch in a nice good reproduction suitable for assembly on Type 2 buses from 08/58-07/67.

Side ladder for roof rack, Stainless steel

4870-230  Type 2 08/67-07/79These ladders in stainless steel are a supplement to our range of roof racks for Type 2, that we already had in our assortment since last year (4870-220/ 4870-221/ 4870-222). Due to success of these items we’ve decided to take also the ladders, suitable for assembly on these roof racks, in our assortment. The ladders can be, depending of the purchased item, installed at the rear as well as at the side. You can stow away and fix your luggage in a safe way. From now on available  each from stock.

Rear ladder for roof rack, Stainless steel

4870-231  Type 2 08/67-07/79

Roof rack 2 bows, Stainless steel

4870-250  Type 25The perfect item for the visitor of meetings among us, who have for several times experienced that there is always something missing during their camping adventure. From now you can carry all the attributes for an enjoyable stay: tent, booze, spare wheel, cuddly toys, domestic animals,… everything can go along on this nice looking roof rack made of stainless steel and designed for Type 25 transporter model, which apart from being very practical is also of a very good quality. From now on available each from stock in 2, 3 and 4 bow.

Roof rack 4 bows, Stainless steel

4870-252  Type 25

Rear window seal. deluxe, German quality with preformed corners, each

7407-500  08/67-07/79241 845 521E
This rear window seal in a good German quality with preformed angles and groove for the deluxe molding chrome (# 0318 x 2) is a complement of our wide range of window seals. From now on available each from stock.

Rear hatch hinge beading

7446-250  Type 2 -07/63 211 829 191A
This beading in PVC sits between the rear hatch and the body and prevents that these 2 metallic parts can may contact with one another and can cause rust. Disassembly of the rear hatch can provoke damage of this beading. Replacement will be the only option. From now on available from stock each for 1 vehicle.

Side door stop, 25 mm, 4 pieces

7480-100  -07/67261 829 575
This rubber side door stops can be found at both sides of the single and double cabin versions of Type 2 buses. This rubber stops makes when you open to loading flaps that they don’t come in contact with the body. When they are old stops can harden and will tear and get lost. From now on we can deliver replacing items. Packed per 4 and depending of the model, you’ll need 4 or 6.

Castrol Classic oil

8510-001  XL20W50 1200ppm

(1l)

Castrol Classic oil seems to be the perfect match with our aircooled engines, which explains of course the popularity of this very useful liquid. Cans of 1 gallon/ 4,54 liter (# 8510-004) are very practical for maintenance, though they are not so easy to take along for refill, if necessary. The 1 liter cans 20W50 Castrol oil are available each or per packing unit of 12 pieces.

Radiator antifreeze

8511-150  1.5lFor many among us, fans of the classic VW, it is still an inexplicable riddle why VW has decided at a certain moment to switch over to water cooled engines... What’s more the cooling water has the nasty characteristic to freeze in the winter. This can damage the radiator, water tubes and water pump, which causes in  general awkward costs. For prevention you can add antifreeze cooling oil to the cooling water. Available in barrels of 1,5L, which you need to dilute. 1 on 1 part water gives 3L of cooling liquid with a protection till -36°C / 2 on 3 parts water gives 7,5L cooling liquid with a protection till -24°C and 3 on 2 parts of water results in 7,5L cooling liquid with a protection till -52°C.

Nut

8730-04  M4 Din 934N 11 004 2

Spacer spring

8754-04  M4 Din 137BN 12 224 1

Screw countersunk, rounded head

8769-04-008  M4x8 Din 964N 10 970 1
These assembly parts are very useful on different connections. A nice example for their use is for assembly of door window moldings at the side of the lock on -07/67 Type 2 buses. Each part is available separately.

Windshield, green on top green

8950-006  T2 08/67-07/79Since the establishment of BBT we’ve always tried to supply for all Types a sufficient vast range of second hand windows. Now, almost 25 years later, it becomes  more and more difficult to meet these requirements. Therefore we’ve decided to offer new windows from stock. Good windows are very important and that’s why we’ve been negotiating for a long time with an European manufacturer to guarantee the best price/quality. We’ve added our range with more than 54 new items of car windows, so we can surely say that we’ve a very large range of windows suitable for Type 2 08/67-07/79, Type 3, Karmann Ghia, convertible Beetle and sedan… All windows are available each from stock. They are duly packed in order to avoid damages during transport or handling.

Rear window, heated, green

8950-101  T2 08/67-07/79

Rear window, green

8950-106  T2 08/67-07/79

Ventwing window open left, green

8950-201  T2 08/67-07/79

Ventwing window open right, green

8950-206  T2 08/67-07/79

Ventwing window closed left, green

8950-211  T2 08/67-07/79

Ventwing window closed right, green

8950-216  T2 08/67-07/79

Doorwindow, left, green

8950-301  T2 08/67-07/79

Doorwindow right, green

8950-306  T2 08/67-07/79

Side middle window L/R, green

8950-401  T2 08/67-07/79

Rear side window L/R, green

8950-501  T2 08/67-07/79

Windshield, clear

8960-000  Type 3311 845 101E

Door window, left, clear

8960-300  Type 3

Door window, right, clear

8960-305  Type 3

Windshield, clear on top green

8980-005  Type 14

Windshield, green on top green

8980-006  Type 14

Doorwindow, left

8980-300  Type 14 55-07/59

Doorwindow, right

8980-305  Type 14 55-07/59

Doorwindow, left

8980-310  Type 14 08/59-

Doorwindow, right

8980-315  Type 14 08/59-

Rear side window, left

8980-500  Type 14 -07/59

Rear side window, right

8980-505  Type 14 -07/59

Rear side window, left, pop-out

8980-510  Type 14 08/59-

Rear side window, right, pop-out

8980-515  Type 14 08/59-

Doorwindow, left, convertible

8981-310  Type 14 08/60-

Doorwindow, right, convertible

8981-315  Type 14 08/60-

Ventwing window, left

8994-200  Type 1 08/57-07/64

Ventwing window, right

8994-205  Type 1 08/57-07/64

Doorwindow, left

8994-300  Type 1 08/57-07/64

Doorwindow, right

8994-305  Type 1 08/57-07/64

Rear side window, left

8994-500  Type 1 08/57-07/64

Rear side window, right

8994-505  Type 1 08/57-07/64

Ventwing window, left

8996-200  Type 1 08/64-

Ventwing window, right

8996-205  Type 1 08/64-

Doorwindow, left

8996-300  Type 1 08/64-

Doorwindow, right

8996-305  Type 1 08/64-

Rear side window, left

8996-500  Type 1 08/64-

Rear side window, right

8996-505  Type 1 08/64-

Windshield, convertible, clear

9001-000  1303151 845 101K

Windshield, green on top blue, convertible

9001-005  Type 1 1303

Windshield, green on top green, convertible

9001-006  Type 1 1303

Rear window, beetle convertible, heated, green

9001-106  Type 1 06/74-

Ventwing window, left, convertible

9001-200  Type 1 1303

Ventwing window, left, convertible, green

9001-201  Type 1 1303

Ventwing window, right, convertible

9001-205  Type 1 1303

Ventwing window, right, convertible, green

9001-206  Type 1 1303

Doorwindow, left, convertible

9001-300  Type 1 1303

Doorwindow, left, convertible, green

9001-301  Type 1 1303

Doorwindow, right, convertible

9001-305  Type 1 1303

Doorwindow, right, convertible, green

9001-306  Type 1 1303

Rear side window, left, convertible

9001-500  Type 1 1303

Rear side window, left, convertible, green

9001-501  Type 1 1303

Rear side window, right, convertible

9001-505  Type 1 1303

Rear side window, right, convertible, green

9001-506  Type 1 1303

BBT knitted beanie

9950-000The upcomming winter months in mind, it seemed a very practical idea to take these knitted bonnets in our assortment. No more cold ears and you can drive in your convertible with less ideal weather conditions!